2024 Latest 100% Exam Passing Ratio - LEED-Green-Associate Dumps PDF
Pass Exam With Full Sureness - LEED-Green-Associate Dumps with 275 Questions
NEW QUESTION # 22
Waste water from kitchen sinks is considered blackwater unless
- A. local codes state otherwise
- B. it is only used for drip irrigation
- C. a CIR is submitted and approved
- D. it is for use in toilets
Answer: A
Explanation:
Explanation
Blackwater is wastewater that contains fecal matter and pathogens, such as from toilets. Greywater is wastewater that is less contaminated, such as from showers, sinks, and washing machines1. However, the classification of kitchen sink wastewater may vary depending on local codes and regulations. Some states and authorities consider kitchen sink wastewater as blackwater because it may contain food waste and germs123. Others consider it as greywater if it meets certain quality standards and is used for beneficial purposes, such as irrigation or toilet flushing45. A CIR (Credit Interpretation Request) is a process to seek clarification on a specific credit or prerequisite in a LEED rating system, but it does not change the definition of blackwater or greywater.
References:
Greywater Reuse | WaterSense | US EPA4
Greywater - California Department of Water Resources5
What Is Greywater? What Is Blackwater? | HomeServe USA1
Grey Water / Reclaimed Water | University of Maryland Extension2
What is meant by the terms Gray water and black water3
Credit Interpretation Requests (CIRs) | U.S. Green Building Council
NEW QUESTION # 23
An annual survey is given to the building occupants in which they are asked to rate their comfort level with regards to the heating and air-conditioning, acoustics, air quality, lighting levels and cleanliness. Which building staff member is best equipped to evaluate the responses and develop a corrective action plan to address problems and improve occupants' comfort?
- A. Commissioning (Cx) Agent
- B. Facilities Manager
- C. LEED AP
- D. Leasing Agent
Answer: B
Explanation:
Explanation
The Facilities Manager is typically responsible for ensuring the comfort and safety of a building's occupants.
They would be best equipped to evaluate responses to a survey about comfort levels in the building and develop a corrective action plan to address any problems identified. References: LEED Green Associate Candidate Handbook, U.S. Green Building Council resources
NEW QUESTION # 24
Which of the following is an appropriate usage of U.S. Green Building Council (USGBC) terminology for a LEED project?
- A. LEED certified building
- B. LEED Registered, Gold Building
- C. LEED Accredited Building
- D. LEED's certified building
Answer: A
Explanation:
The term "LEED certified building" is the correct usage according to the U.S. Green Building Council (USGBC). This term indicates that a building has met the standards set by the LEED rating system and has been officially certified by the USGBC. Reference: LEED Green Associate Candidate Handbook, U.S. Green Building Council resources
NEW QUESTION # 25
Which impact category is weighted the most in the LEED rating systems?
- A. Human Health
- B. Biodiversity
- C. Water Resources
- D. Climate Change
Answer: D
Explanation:
Climate change is weighted the most in the LEED rating systems because it is considered the most urgent and significant environmental challenge facing humanity. Climate change is caused by the accumulation of greenhouse gases in the atmosphere, which trap heat and alter the global climate patterns. Climate change can have severe consequences for human health, biodiversity, water resources, food security, and social equity. LEED projects can help mitigate climate change by reducing greenhouse gas emissions from building operations and materials, as well as enhancing resilience and adaptation to climate impacts. The LEED impact categories and point allocation process assigns 35% of the total points to climate change. Reference: LEED v4 Impact Category and Point Allocation Process Overview2; LEED v4 BD+C Reference Guide, Introduction, page 9
NEW QUESTION # 26
What is the minimum gross floor area required for a Building Design and Construction (BD+C) project to be eligible for certification?
- A. 500 ft2 (46 m2)
- B. 750 ft2 (70 m2)
- C. 1000 tt2 (93 m2)
- D. 250 ft2 (23 m2)
Answer: C
Explanation:
Explanation
The LEED minimum program requirements state that for LEED BD+C and LEED O+M rating systems, the LEED project must include a minimum of 1000 ft2 (93 m2) of gross floor area1.
References:
LEED v4: Building Design + Construction Guide
LEED minimum program requirements
LEED For Building Design And Construction (LEED BD+C) Rating Systems In Details
NEW QUESTION # 27
According to the LEED Minimum Program Requirements (MPR) specifying minimum occupancy rates, a project must serve how many occupants?
- A. Five FTEs for six months
- B. 50% of occupancy based on code
- C. At least two FTEs, no later than SIX months after Commissioning (Cx)
- D. One or more Full Time Equivalents (FTEs)
Answer: D
Explanation:
Explanation
According to the LEED v4 Minimum Program Requirements (MPRs), there is no minimum required number of occupants or full-time equivalents (FTEs) for which a building must be designed to be considered eligible to pursue certification1. However, the project must serve at least one FTE, which is based on an 8-hour day2.
The other options are not part of the MPRs.
References:
Minimum Program Requirements (MPRs) - U.S. Green Building Council1
LEED 101: MPRs (Minimum Program Requirements)2
NEW QUESTION # 28
What is the best way to prevent a building's indoor pollutant(s)?
- A. Monitor carbon dioxide
- B. Test for radon
- C. Eliminate or control pollutants at the source
- D. Remove any pollutants that enter the building
Answer: C
Explanation:
The best way to prevent a building's indoor pollutant(s) is to eliminate or control pollutants at the source. Indoor pollutants are substances or particles that can adversely affect the indoor air quality (IAQ) of a building and the health, comfort, and productivity of the occupants. Indoor pollutants can originate from various sources, such as building materials, furnishings, cleaning products, combustion appliances, outdoor air, or occupant activities. Eliminating or controlling pollutants at the source can prevent them from entering or spreading in the indoor environment, which can reduce the exposure and risk for the occupants. Some examples of source control strategies are: using low-emitting materials, installing local exhaust ventilation, sealing combustion appliances, implementing green cleaning practices, and prohibiting smoking13. Reference: LEED v4 Green Associate Candidate Handbook1, EPA's Indoor Air Quality3
NEW QUESTION # 29
In addition to the temperature and air movement, what is another factor to consider when implementing Thermal Comfort strategies?
- A. Carbon dioxide concentrations
- B. Methane off-gassing
- C. Humidity
- D. Combustion processes from vehicles
Answer: C
Explanation:
Explanation
In addition to temperature and air movement, humidity is another factor to consider when implementing thermal comfort strategies. Humidity is the amount of water vapor in the air, which affects how warm or cool people feel. High humidity can make people feel hotter and more uncomfortable, while low humidity can cause dryness and irritation of the skin, eyes, nose, and throat. Thermal comfort strategies should aim to maintain an optimal level of humidity that balances human comfort and health with energy efficiency and moisture control. The other options are not factors to consider when implementing thermal comfort strategies.
Methaneoff-gassing is the release of methane gas from organic matter decomposition or anaerobic digestion, which contributes to greenhouse gas emissions and climate change. Carbon dioxide concentrations are a measure of indoor air quality that indicates the level of ventilation and fresh air supply in a space. Combustion processes from vehicles are sources of outdoor air pollution that emit carbon monoxide, nitrogen oxides, particulate matter, and other harmful substances. References: LEED Green Associate Candidate Handbook, page 29; USGBC, [Indoor Environmental Quality], page 2.
NEW QUESTION # 30
Which credit category attempts to reduce light pollution and discourages the development of previously undeveloped land?
- A. Sustainable Sites
- B. Regional Priority
- C. Energy and Atmosphere
- D. Location and Transportation
Answer: A
NEW QUESTION # 31
Which construction pollution can be reduced by prevention activities?
- A. High-reflectance materials
- B. Infiltration
- C. Blackwater creation
- D. Airborne dust generation
Answer: D
Explanation:
Explanation
One type of construction pollution that can be reduced by prevention activities is airborne dust generation.
Airborne dust can be generated by various construction activities, such as excavation, demolition, grading, hauling, and vehicle traffic. Airborne dust can have negative impacts on the air quality, human health, and climate. Airborne dust can contribute to respiratory problems, allergies, asthma, and eye irritation for workers and nearby residents. Airborne dust can also reduce the visibility, increase the risk of accidents, and damage the equipment and materials. Airborne dust can also affect the climate by absorbing or reflecting solar radiation, altering the cloud formation and precipitation patterns, and influencing the carbon cycle1.
Some of the prevention activities that can reduce airborne dust generation during construction are12:
Covering or wetting the exposed soil and stockpiles
Using water sprays or misters to suppress the dust
Installing wind fences or barriers around the site
Applying mulch, straw, or vegetation to stabilize the soil
Sweeping or vacuuming the paved areas and roads
Limiting the speed and frequency of vehicles
Using low-emission or electric vehicles and equipment
Implementing a dust control plan and monitoring the dust levels
NEW QUESTION # 32
What is the percentage rule when making a decision on the rating system that is most appropriate to use for a project?
- A. 30/70 rule
- B. 50/50 rule
- C. 40/60 rule
- D. 60/40 rule
Answer: C
Explanation:
Explanation
The percentage rule is a method to determine the most appropriate LEED rating system for a project when several rating systems may be applicable1. To use this rule, first assign a rating system to each square foot or square meter of the building, and then choose the most appropriate rating system based on the resulting percentages1. The entire gross floor area of a LEED project must be certified under a single rating system and is subject to all prerequisites and attempted credits in that rating system1. The percentage rule states that if one rating system covers more than 60% of the gross floor area, that rating system should be used1. If no rating system covers more than 60% of the gross floor area, but one covers more than 40%, then that rating system should be used1. If no rating system covers more than 40% of the gross floor area, then the project team can choose any applicable rating system1. Therefore, the answer is B. 40/60 rule.
References: =
LEED rating system selection guidance
NEW QUESTION # 33
According to the Indoor Environmental Quality credit category, which of the following is considered an unoccupied space?
- A. Restroom
- B. Corridor
- C. School classroom
- D. Mechanical and electrical rooms
Answer: D
NEW QUESTION # 34
Which of the following is an Environmental Concern when referring to Energy and Atmosphere?
- A. Use of native species
- B. Ventilation levels
- C. Occupant comfort
- D. Resource depletion
Answer: D
Explanation:
Explanation
Resource depletion is a major environmental concern related to energy use. The extraction and use of non-renewable energy resources (such as fossil fuels) can lead to their depletion over time. This is why strategies that reduce energy use or utilize renewable energy sources are important in green building practices. References: LEED Green Associate Candidate Handbook, U.S. Green Building Council resources
NEW QUESTION # 35
What standard ensures adequate ventilation is supplied to building occupants?
- A. ASHRAE 62.1
- B. ASHRAE 189.1
- C. ASHRAE 55
- D. ASHRAE 90.1
Answer: A
NEW QUESTION # 36
Which of the following standards addresses guidance for sustainable construction in complying with building codes?
- A. ASHRAE 72
- B. ASHRAE 189.1
- C. ASHRAE 62.1
- D. ASHRAE 90.1
Answer: B
NEW QUESTION # 37
Which of the following principles is a part of the integrated process?
- A. Systems thinking
- B. Building information modeling
- C. Cradle-to-cradle
- D. Project scheduling
Answer: A
NEW QUESTION # 38
The maximum number of credits that can be achieved under Energy and Atmosphere category for Building Design and Construction: New Construction and Major Renovation is
- A. 0
- B. 1
- C. 2
- D. 3
Answer: C
Explanation:
Explanation
According to the LEED credit library, the Energy and Atmosphere category for Building Design and Construction: New Construction and Major Renovation has 6 prerequisites and 11 credits, with a total of 33 possible points. The prerequisites are:
Fundamental Commissioning and Verification (required)
Minimum Energy Performance (required)
Building-Level Energy Metering (required)
Fundamental Refrigerant Management (required)
Construction Activity Pollution Prevention (required)
Advanced Energy Metering (required)
The credits are:
Enhanced Commissioning (2-6 points)
Optimize Energy Performance (1-18 points)
Advanced Energy Metering (1 point)
Demand Response (1-2 points)
Renewable Energy Production (1-3 points)
Enhanced Refrigerant Management (1 point)
Green Power and Carbon Offsets (1-2 points)
NEW QUESTION # 39
......
Verified LEED-Green-Associate dumps Q&As - 100% Pass from Exam4PDF: https://www.exam4pdf.com/LEED-Green-Associate-dumps-torrent.html
Pass LEED-Green-Associate Exam in First Attempt Guaranteed 2024 Dumps: https://drive.google.com/open?id=1Mc5DE4AgoOGiyUh0syX8WXS3OUH2cuyI
