Free Sales Ending Soon - Use Real D-PST-MN-A-24 PDF Questions [Dec 09, 2024]
Updated Dec-2024 Exam D-PST-MN-A-24 Dumps - Pass Your Certification Exam
EMC D-PST-MN-A-24 Exam Syllabus Topics:
| Topic | Details |
|---|---|
| Topic 1 |
|
| Topic 2 |
|
| Topic 3 |
|
| Topic 4 |
|
| Topic 5 |
|
NEW QUESTION # 30
How many fan module failures can a node tolerate?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: A
Explanation:
A Dell EMC PowerStore node can tolerate one fan module failure. The system is designed with redundancy to ensure that if a single fan module fails, the remaining fan modules can compensate for the loss and maintain proper cooling to prevent overheating1. The system will increase the speed of the remaining fans to ensure continued cooling.
When a fan module failure occurs, the system will generate an alert to notify the administrator of the fault. The administrator should then take the following steps:
Acknowledge the alert in the PowerStore Manager.
Plan for the replacement of the faulted fan module as soon as possible to restore full redundancy.
Follow the replacement procedures as outlined in the Dell PowerStore Installation and Service Guide1.
It is important to address fan module failures promptly to ensure the long-term health and performance of the PowerStore system. The increased fan speed is a temporary measure to maintain operations until the faulted fan module can be replaced.
NEW QUESTION # 31
Under which condition does the Dell EMC PowerStore equipment in the rack require additional stability?
- A. Unstable humidity
- B. High temperatures
- C. Low temperatures
- D. When shipping the system
Answer: D
Explanation:
When shipping the system, additional stability is necessary to ensure that the equipment remains secure and undamaged during transportation. Proper stabilization prevents any potential movement or impact that could harm the delicate components of the system.
NEW QUESTION # 32
A Storage Administrator has an existing single appliance Dell EMC PowerStore 3000T cluster. An additional PowerStore 9000T has been purchased to add into the existing cluster.
How does the administrator proceed?
- A. Additional VLT links on the ToR switching must be configured for the 9000T to support the increased inter-switch network load
- B. Add the new 9000T appliance into the cluster per the procedure; mixed models of the same type are supported
- C. The new appliance cannot be added to the cluster; appliance model and type must match when clustering appliances together
- D. Remove two of the four NVMe NVRAM drives from the 9000T; the caching configuration of all clustered appliances must match
Answer: B
Explanation:
The correct procedure for a Storage Administrator to add a new PowerStore 9000T appliance into an existing single appliance Dell EMC PowerStore 3000T cluster is to add the new 9000T appliance into the cluster per the procedure; mixed models of the same type are supported.
Dell PowerStore allows for the addition of appliances to an existing cluster, enabling both scaling up and scaling out.
When adding a new appliance to an existing cluster, it is important to ensure that the appliance is uninitialized and that both the new appliance and the existing cluster are in a healthy state1.
The process of adding an appliance is facilitated through the PowerStore Manager. The administrator should navigate to the Hardware page and click the Add button to present the available unconfigured appliances that can be added1.
It is not necessary to configure additional VLT links on the ToR switching specifically for the 9000T to support the increased inter-switch network load as part of the initial addition process1.
There is no requirement that the appliance model and type must match when clustering appliances together, allowing for mixed models of the same type within a cluster1.
Removing NVMe NVRAM drives from the 9000T is not a standard procedure for clustering and is not required for the caching configuration of all clustered appliances to match1.
For detailed procedures on adding appliances to a Dell EMC PowerStore cluster, it is recommended to refer to the official Dell PowerStore Clustering and High Availability documentation or contact Dell EMC support for guidance.
NEW QUESTION # 33
Under which condition does the Dell EMC PowerStore equipment in the rack require additional stability?
- A. Unstable humidity
- B. High temperatures
- C. Low temperatures
- D. When shipping the system
Answer: D
Explanation:
The Dell EMC PowerStore equipment in the rack requires additional stability when shipping the system.
When preparing Dell EMC PowerStore equipment for shipping, it is crucial to ensure that the system is stable and secure to prevent any damage during transit.
Additional stability measures might include securing the equipment within the rack using appropriate brackets, using pallets designed for shipping heavy equipment, and ensuring that the rack is properly balanced.
The need for additional stability is not typically associated with environmental conditions such as humidity or temperature but is a standard precaution during the physical movement of the system to safeguard against vibrations, shocks, and impacts that can occur during shipping1.
For detailed procedures and best practices regarding the shipping and handling of Dell EMC PowerStore equipment, it is recommended to consult the official Dell EMC PowerStore documentation or contact Dell EMC support.
NEW QUESTION # 34
Which network is used for intra-cluster management?
- A. Storage network
- B. NAS network
- C. Service network
- D. Internal network
Answer: D
Explanation:
For intra-cluster management within Dell EMC PowerStore systems, the internal network is used. This network is specifically named the Intra-Cluster Management (ICM) and Intra-Cluster Data (ICD) networks. Each node in a PowerStore cluster communicates with other nodes through bonded ports that are part of this internal network12.
The ICM and ICD networks are crucial for the cluster's operation as they allow for the management and coordination of data across the cluster. In multi-appliance PowerStore clusters, these networks communicate through the top-of-rack switch network with untagged VLAN network packets that have auto-generated IPv6 addresses. For single-appliance clusters, starting in PowerStoreOS 1.0.2, the ICM network communicates through the backplane within the appliance instead of through the top-of-rack switch2.
In summary, the internal network is essential for the functioning of a PowerStore cluster as it facilitates the necessary communication between nodes for management and data operations. This design ensures high availability and efficient management of the storage system.
NEW QUESTION # 35
From where can a data collection be initialized within Dell EMC PowerStore Manager?
- A. Node, storage resource, and alerts
- B. Appliance, node, and storage resource
- C. Cluster, appliance, and event log
- D. Cluster, appliance, and alerts
Answer: D
Explanation:
A data collection in Dell EMC PowerStore Manager can be initiated from the cluster, appliance, and alerts sections within the PowerStore Manager user interface. This process is essential for gathering system logs and other information that can be used for troubleshooting or analysis.
To initiate a data collection, follow these steps:
Log into the PowerStore Manager user interface.
Navigate to the 'Settings' menu.
Go to the 'Support' section.
Select 'Gather Support Materials'.
Choose the scope of the data collection, which can be at the cluster level, for a specific appliance, or related to certain alerts.
Click the 'Gather Support Materials' button to start the collection process.
Monitor the progress in the 'Jobs' section of PowerStore Manager or within the 'Support Materials' section1.
It is important to note that the data collection process may take some time to complete, depending on the amount of data and the system's performance. Once the data collection is finished, the gathered materials can be used by Dell EMC support for further analysis or can be reviewed by the storage administrator to address any issues1. For more detailed instructions on data collection, refer to the Dell EMC PowerStore documentation or the support knowledge base articles provided by Dell23. Following these guidelines ensures that the data is collected correctly and efficiently.
NEW QUESTION # 36
Which component is only replaceable by qualified personnel?
- A. Base enclosure
- B. Power supply
- C. Memory module
- D. Embedded I/O module
Answer: A
Explanation:
The base enclosure is a component that is typically only replaceable by qualified personnel. This is because the base enclosure of a Dell PowerStore system contains critical components and connections that require specialized knowledge and tools to handle properly. Replacing a base enclosure involves understanding the system's architecture, safely disconnecting and reconnecting various components, and ensuring that the system is not compromised during the process.
The memory module, embedded I/O module, and power supply are designed to be more accessible for replacement and may fall under the category of customer-replaceable units (CRUs) or field-replaceable units (FRUs), depending on the specific model and configuration of the PowerStore system1.
For detailed procedures on replacing the base enclosure or any other components, it is recommended to refer to the official Dell PowerStore Installation and Service Guide. This guide provides step-by-step instructions and safety precautions for qualified personnel to follow when performing hardware replacements1. It is crucial to adhere to these guidelines to maintain system integrity and ensure that the storage system continues to operate effectively after the replacement.
NEW QUESTION # 37
A Storage Administrator needs to add drives to a base enclosure of a Dell EMC PowerStore 3000X system. The system currently contains 10 750-GB NVMe SCM drives.Which drive configuration maximizes the base enclosure capacity?
- A. 11 15360-GB NVMe SSD drives in slots 10-20
- B. 13 750-GB NVMe SCM drives in slots 10-22
- C. 13 15360-GB NVMe SSD drives in slots 10-22
- D. 11 750-GB NVMe SCM drives in slots 10-20
Answer: C
NEW QUESTION # 38
What is the protocol used for the storage network?
- A. FC
- B. SMB
- C. NFS
- D. iSCSI
Answer: A
Explanation:
The protocol used for the storage network in Dell PowerStore systems is Fibre Channel (FC). FC is a high-speed network technology primarily used for storage networking. Dell PowerStore utilizes FC as part of its all-NVMe design, which also includes NVMe-over-fabric networking to deliver low latency performance for storage workloads1.
Fibre Channel provides several benefits for storage networks, including:
High throughput and low latency for storage operations.
Support for long-distance networking, which is beneficial for disaster recovery and remote backups.
A mature and widely supported ecosystem with a variety of hardware and software options.
For detailed information on configuring and using FC with Dell PowerStore, administrators should refer to the Dell PowerStore Networking Guide for Storage Services and the Dell PowerStore Best Practices Guide. These documents provide comprehensive instructions on network configurations, including best practices for setting up and managing FC networks within Dell PowerStore environments23. Following these guidelines ensures optimal performance and reliability of the storage network.
NEW QUESTION # 39
While on-site troubleshooting a Dell EMC PowerStore system, the node B embedded module fault LED is blinking blue and amber alternating at one second intervals. What does this indicate?
- A. System is not initialized
- B. Node is in degraded mode
- C. Node is in service mode
- D. Node is booting
Answer: C
Explanation:
When the node B embedded module fault LED on a Dell EMC PowerStore system is blinking blue and amber alternating at one-second intervals, it indicates that the node is in service mode1. Service mode is a state where the node is not in normal operation and may be undergoing maintenance or diagnostics.
In service mode, the node is typically isolated from normal storage operations to allow for troubleshooting, hardware replacement, or software updates without affecting the rest of the system. The alternating blue and amber LED is a visual indicator used by technicians to identify the current state of the node.
To return the node to normal operation, the service task must be completed, and the node must be taken out of service mode using the appropriate commands through the system's management interface. For detailed procedures on managing nodes in service mode, refer to the Dell EMC PowerStore Service Manual or contact Dell EMC Support for guidance2.
NEW QUESTION # 40
Which component is an FRU?
- A. Nodes
- B. DIMMs
- C. Battery Backup Unit
- D. Embedded IO Module
Answer: C
Explanation:
A Field Replaceable Unit (FRU) is a component that can be replaced by the user or technician without having to send the entire product or system to a repair facility. Dell's Customer Replaceable Unit (CRU) program allows customers to replace designated hardware components, which are typically considered as FRUs1.
In the context of Dell PowerStore Maintenance, the Battery Backup Unit (BBU) is considered an FRU because it is designed to be easily replaced in the field. The BBU is critical for maintaining power to the system in the event of a power failure, ensuring that data is not lost and the system can be shut down gracefully.
The other components listed, such as DIMMs, Embedded IO Modules, and Nodes, may not be as easily replaceable by the customer or may require more technical expertise or special tools. Therefore, they are not typically classified as FRUs within the Dell PowerStore ecosystem.
For detailed procedures on replacing the BBU or any other FRU components, it is recommended to refer to the official Dell PowerStore Maintenance documents and follow the guidelines provided for safe and effective replacement. This ensures that the system integrity is maintained and any warranty or support agreements remain valid.
NEW QUESTION # 41
What is an alternative way to collect logs instead of using the Dell EMC PowerStore manager GUI?
- A. USB stick inserted into the system
- B. Discovery Utility
- C. Data Collect using Service Container
- D. Data Collect using vCenter
Answer: C
Explanation:
An alternative way to collect logs instead of using the Dell EMC PowerStore manager GUI is Data Collect using Service Container.
The Dell EMC PowerStore provides multiple methods for collecting logs for troubleshooting and analysis.
While the PowerStore Manager GUI is a common method, using the Service Container via SSH/CLI is an alternative way to gather logs1.
This method involves connecting to the PowerStore system's Service Container through SSH and running specific service commands to collect the required logs.
The commands svc_dc download -h or svc_dc upload -h can be used to download or upload logs directly from and to the system1.
This process is particularly useful when the GUI is not accessible or when directed by Dell Support to collect more detailed logs for complex issues.
For detailed instructions on log collection using the Service Container, refer to the Dell PowerStore Service Scripts Guide or contact Dell Support for assistance.
NEW QUESTION # 42
While on-site installing a Dell EMC PowerStore T system, the node A embedded module management Ethernet port link LED is off. What does this indicate?
- A. Port speed is 10 GB/s
- B. Network connection is established
- C. No network connection is established
- D. Port speed is 1 GB/S
Answer: C
Explanation:
When the link LED of the node A embedded module management Ethernet port is off, it indicates that there is no network connection established. The link LED is typically used to indicate the presence of a network connection and its status. If the LED is off, it means that the Ethernet port is not currently connected to a network or there is an issue preventing the connection from being established1.
In the case of the Dell EMC PowerStore T system, the embedded module management Ethernet ports are used for network management traffic. It is essential that these ports have an active network connection for the system to be managed remotely. If the link LED is off, the following steps should be taken:
Check the physical connection of the Ethernet cable to ensure it is securely plugged into both the node's port and the corresponding switch or router port.
Verify that the switch or router is powered on and functioning correctly.
Ensure that the correct port on the switch or router is being used and that it is configured correctly for the PowerStore system.
If the issue persists after checking the physical connections and switch/router configuration, consult the Dell EMC PowerStore T Installation and Service Manual for further troubleshooting steps2.
It is important to resolve any network connection issues promptly to maintain the manageability and accessibility of the PowerStore system. Following the official Dell documentation and support resources will help ensure that the system is installed and configured correctly for optimal performance and reliability.
NEW QUESTION # 43
Which type of device is supported in expansion enclosures?
- A. SAS SSD
- B. NVMe NVRAM
- C. NVMe SSD
- D. NVMe SCM
Answer: C
Explanation:
The type of device supported in expansion enclosures for Dell PowerStore systems is NVMe SSD.
Starting with PowerStoreOS 3.0, the PowerStore models 500, 1200, 3200, 5200, and 9200 support 24-drive 2U NVMe expansion enclosures using 2.5-inch NVMe SSD drives for additional capacity1.
The NVMe expansion enclosures do not support NVMe SCM drives1.
The base enclosure can support all NVMe SSDs or a mix of NVMe SSDs and NVMe SCM drives (for the metadata tier) with an NVMe expansion enclosure attached1.
Before attaching an NVMe expansion enclosure, all drive slots 0 to 21 in the base enclosure must be populated1.
Each appliance in a PowerStore cluster supports up to three NVMe expansion enclosures1.
For more detailed information on the supported devices in expansion enclosures for Dell PowerStore systems, you can refer to the Dell PowerStore: Technical Primer1.
NEW QUESTION # 44
Which account credentials are needed to run diagnostic commands?
- A. console
- B. root
- C. service
- D. admin
Answer: C
Explanation:
The account credentials needed to run diagnostic commands on Dell PowerStore Maintenance are for the service account.
The service account is specifically designed for performing specialized service functions, including running diagnostic commands1.
To run service commands, you would typically:
Enable SSH in PowerStore Manager under Settings.
Use an SSH client to connect to the management IP.
Log in using the username and password for the service account2.
The service account has the necessary permissions to execute service scripts and commands that are used for diagnostics and troubleshooting3.
It is important to note that the service account password should be changed from the default during the initial configuration of the appliance for security purposes1.
For more detailed information on using the service account for diagnostics and other service tasks, refer to the Dell PowerStore Service Scripts Guide or contact Dell Support.
NEW QUESTION # 45
Refer to the exhibit.
Refer to the exhibit.
What Dell EMC PowerStore ToR front-end cabling is shown?
- A. VLT interconnectivity
- B. OOB Management
- C. Core switch uplink
- D. Management and discovery
Answer: A
NEW QUESTION # 46
Which network traffic is encrypted using IPsec?
- A. Management network
- B. Storage network
- C. Internal network
- D. Service network
Answer: A
Explanation:
In Dell PowerStore systems, IPsec is used to encrypt traffic for the management network. IPsec (Internet Protocol Security) is a suite of protocols designed to ensure the integrity, confidentiality, and authentication of data communications over an IP network. Encrypting the management network traffic with IPsec is a best practice to secure communication between the management console and the storage system, protecting against potential eavesdropping and unauthorized access1.
The management network is responsible for the overall administration and operation of the storage system, including configuration management, performance monitoring, and system updates. By encrypting this traffic, Dell PowerStore ensures that sensitive management operations are secured.
For detailed information on configuring IPsec for the management network and other best practices for network security within Dell PowerStore environments, users should refer to the official Dell PowerStore documentation, such as the Deployment KB: PowerStore: User Network Firewall Rules Tool and the Dell PowerStore Best Practices Guide12. These documents provide comprehensive guidelines on network configurations, including firewall rules and encryption settings, to maintain the highest levels of security and system integrity.
NEW QUESTION # 47
Which component can be replaced while the Dell EMC PowerStore is up and running?
- A. M.2 Device
- B. 4-Port Mezz card
- C. LCC
- D. SFP
Answer: D
Explanation:
The component that can be replaced while the Dell EMC PowerStore is up and running is SFP (Small Form-factor Pluggable).
SFP modules are hot-swappable, meaning they can be replaced without powering down the system.
These modules are used for network connections and can be found in the network ports of the PowerStore appliance.
When replacing an SFP, it is important to ensure that the replacement is of the same type and speed as the one being replaced.
The process typically involves:
Removing the network cable from the SFP.
Unlocking the SFP from its socket.
Pulling the SFP out of the socket.
Inserting the new SFP into the socket until it clicks into place.
Reconnecting the network cable1.
For more detailed procedures on replacing SFP modules or other components, refer to the Dell PowerStore Installation and Service Guide or contact Dell Support for assistance.
NEW QUESTION # 48
......
D-PST-MN-A-24 Dumps To Pass Storage Administrator Exam in One Day: https://www.exam4pdf.com/D-PST-MN-A-24-dumps-torrent.html
Latest Real EMC D-PST-MN-A-24 Exam Dumps Questions: https://drive.google.com/open?id=1TljEqbVdilXxgzQZIakypR729WKBRs6z
