NACE-CIP1-001 Premium PDF & Test Engine Files with 100 Questions & Answers
Get 100% Real NACE-CIP1-001 Exam Questions, Accurate & Verified Answers As Seen in the Real Exam!
NEW QUESTION # 30
Relative humidity is
- A. a measure of the amount of moisture in the air compared to the air temperature.
- B. a measure of the amount of moisture in the air compared to saturation level.
- C. the lowest temperature at which moisture forms on a steel surface.
- D. the highest temperature at which moisture forms on a steel surface.
Answer: B
NEW QUESTION # 31
Check abrasive blast pressure with a
- A. surface comparator
- B. replica tape
- C. needle pressure gauge
- D. nozzle aperature gauge
Answer: C
NEW QUESTION # 32
Removal of surface contaminants is done by:
- A. Abrasive blasting
- B. Waterjetting
- C. Scarifying
- D. A combination of methods
Answer: D
NEW QUESTION # 33
What is the minimum spot measurement value allowed by SSPC-PA 2 in each 10 m2 (100 ft2) area?
- A. 80% of the specified minimum thickness
- B. 100% of the specified maximum thickness
- C. 90% of the specified maximum thickness
- D. 70% of the specified maximum thickness
Answer: A
NEW QUESTION # 34
You are the NACE Coating Inspector on an exterior job where the contractor is not using any environmental controls, For the last several hours your reading; indicate the relative humidity is rising and the substrate temperature is dropping. The sky is clouding over and the weather forecast is for evening showers. It is now 4 PM, your readings indicate you have minimally acceptable environmental conditions, however if the current trend continues, you expect to be outside specified conditions soon. The contractor advises you he is going to mix up the next full kit to complete his for the day.
Your FIRST preformed course of action is to:
- A. Advise the Contractor he can proceed
- B. Advise the Contractor of your readings
- C. Advise the Contractor he cannot proceed
- D. Call your supervisor
Answer: B
NEW QUESTION # 35
Excess moisture during holiday testing can cause erroneous indications by creating a path across the surface of the coating to pinholes previously detected, or directly to the signal return connection.
This is often referred to as:
- A. monitoring
- B. juxtaposing.
- C. telegraphing.
- D. transitioning.
Answer: C
NEW QUESTION # 36
To achieve consistently accurate results with ALL alt test equipment
- A. wash your hands before sampling.
- B. wear gloves when sampling.
- C. avoid placing the sample discs on a surface.
- D. calibrate the instrument in the field.
Answer: A
NEW QUESTION # 37
Daily reports are important because:
Select All That Apply
- A. Management uses them to make personnel decisions.
- B. Inspectors rarely change on a project.
- C. the information impacts future projects.
- D. The information aids communication with supervisors.
Answer: A,C,D
NEW QUESTION # 38
You are the NACE Inspector on a job where the Owner's specification requites you to perform a twice daily check of blast pressure at the nozzle. It is now day 30 on the job and all of your readings have been within compliance. The Contractor complains that these checks taking up much time and in view of the compliant results they are unnecessary.
Your FIRST preferred course of action is to:
- A. Keep doing the checks regardless
- B. Skip the checks as you are. confident the blast pressure is OK
- C. Keep doing the checks and consult the Owner's representative for direction
- D. Skip the checks and just record the same readings as you have been getting
Answer: C
NEW QUESTION # 39
When using the ISO comparator in accordance with ISO 8503, if the surface profile does not directly compare to one of the four segments the inspector should:
- A. Record the segment with the more aggressive profile
- B. Use another method as the comparator method is too subjective
- C. Record the segment with the less aggressive profile
- D. Record your result by identifying two segments
Answer: C
NEW QUESTION # 40
The primary difference between Non-Convertible vs. Convertible coatings is:
- A. Convertible coatings do not undergo a chemical change during curing whereas Non-Convertible coatings do
- B. Convertible coatings cure solely by solvent evaporation whereas Non-Convertible coatings do not
- C. Non-Convertible coatings cure by co-reaction whereas Convertible coatings do not
- D. Non-convertible coatings do not undergo a chemical change during curing whereas Convertible coatings do
Answer: D
NEW QUESTION # 41
Dew point is the temperature at which
- A. the air is saturated.
- B. humidity decreases
- C. condensation occurs.
- D. water freezes.
Answer: C
NEW QUESTION # 42
ISO SA 2 is defined as:
- A. Very Thorough Blast Cleaning
- B. Near White Metal Blasting
- C. Light Blast Cleaning
- D. Thorough Blast Cleaning
Answer: D
NEW QUESTION # 43
If the project specification DOES NOT state the specific DFT measurement standards, the inspector should use
- A. a detailed checklist and document the lack of a standard.
- B. NACE 2/SSPC SP10
- C. a recognized industry standard like SSPC-PA 2 that is broadly accepted
- D. their best judgment based on similar projects and specifications.
Answer: C
NEW QUESTION # 44
Corrosion generally occurs at which of the following sites:
- A. Cathode
- B. Anode
- C. Metallic pathway
- D. Electrolyte
Answer: B
NEW QUESTION # 45
You are the NACE Inspector on a 5000 sq. ft. job where SSPC PA 2 has been specified.
Assuming all areas are in compliance, how many gauge readings and spot measurements are required?
- A. 225 Gauge Readings resulting in 75 Spot Measurements
- B. 105 Gauge Readings resulting in 35 Spot Measurements
- C. 45 Gauge readings resulting in 15 Spot Measurements
- D. 75 Gauge Readings resulting in 25 Spot Measurements
Answer: A
NEW QUESTION # 46
Fine cracks in the surface of a coating that rarely reach the substrate are called
- A. blistering.
- B. alligatoring.
- C. cracking.
- D. checking.
Answer: D
NEW QUESTION # 47
Upon arrival of coating materials, the inspector should
- A. observe and document time frame and environmental conditions between each coat.
- B. observe and document the amount of material and batch numbers.
- C. review coating contractors' plans for storage of coating materials and confirm they meet national, local and owners' fire and environmental regulations.
- D. observe aryl document that the applicator WFT at regular intervals during application.
Answer: B
NEW QUESTION # 48
Which one of these elements is not necessary for corrosion to occur:
- A. Cathode
- B. Reference Cell
- C. Anode
- D. Electrolyte
Answer: B
NEW QUESTION # 49
A magnetic pull-off type gauge is a good choice when:
- A. Accuracy is not required
- B. When working on non-ferrous metals
- C. Performing an adhesion test
- D. When an intrinsically safe tool is required
Answer: D
NEW QUESTION # 50
......
NACE-CIP1-001 Premium Files Practice Valid Exam Dumps Question: https://www.exam4pdf.com/NACE-CIP1-001-dumps-torrent.html
Practice with NACE-CIP1-001 Dumps for CIP Level 1 Certified Exam Questions & Answer: https://drive.google.com/open?id=18PSNzw-_znF5gJ8jBD6mW02GtKtoA_e2
